จัดการฮอตสปอต

อุปกรณ์ที่เพิ่มในแผนที่เรียกว่าฮอตสปอต ฮอตสปอตแสดงตำแหน่งของอุปกรณ์ และคุณสามารถรับข้อมูลการดูสดหรือแจ้งเตือนจากสถานการณ์การเฝ้าดูผ่านฮอตสปอตได้

เพิ่มกล้องเป็นฮอตสปอต

คุณสามารถเพิ่มกล้องลงในแผนที่เป็นฮอตสปอตได้

ก่อนเริ่มต้น

Make sure you have added an e-map and a camera to the client. See Add Map and Device Management for details.

ขั้นตอน

1. Enter the E-map page.
2. Click Edit in the upper-right corner to enter the map editing mode.
3. Click Add Hot Spot → Camera Hot Spot to open the Add Hot Spot window.

4. Select the cameras to be added to the map.
5. ตัวเลือก: Edit the hot spot name, select the name color and select the hot spot icon.
6. คลิก ตกลง เพื่อบันทึกการตั้งค่า

The camera icons are added on the map as hot spots and the icons of the added cameras in the group list change. The sector indicates the camera's field of view.

7. Perform the following operation(s).

เพิ่มอินพุตเตือนภัยเป็นฮอตสปอต

You can add the alarm inputs to the map as hot spots.

ขั้นตอน

1. Enter the E-map module.
2. Click Edit in the upper-right corner to enter the map editing mode.
3. Click Add Hot Spot → Alarm Input Hot Spot to open the Add Hot Spot window.

4. Select the alarm inputs to be added to the map.
5. ตัวเลือก: Edit hot spot name, select the name color and select the hot spot icon by double-clicking the corresponding field.
6. คลิก ตกลง

The alarm input icons are added to the map as hot spots and the icons of the added alarm inputs in the group list change.

7. ตัวเลือก: Drag the hot spot to move it to a certain position.

เพิ่มเอาต์พุตเตือนภัยเป็นฮอตสปอต

You can add alarm outputs to the map as hot spots for management. After that, you can enable or disable it in a quick manner. If you enable an alarm output on the map, the security control devices (e.g. sirens, bells) connected to it will alarm for attention.

ก่อนเริ่มต้น

Make sure you have added an e-map and alarm output to the client. See Add Map and Device Management for details.

ขั้นตอน

1. Enter the E-map module.
2. Click Edit on the E-map toolbar to enter the map editing mode.
3. Click Add Hot Spot → Alarm Output Hot Spot to open the Add Hot Spot panel.

4. Select the alarm output to be added to the map.
5. ตัวเลือก: Edit the hot spot name, select the name color, and select the hot spot icon.
6. คลิก ตกลง

The alarm output is added to the map as a hot spot and its icon in the group list changes.

7. ตัวเลือก: Drag the alarm output to move it to a certain position.

เพิ่มโซนเป็นฮอตสปอต

You can add zones to the map so that you can quickly locate the zone when an alarm is triggered.

ก่อนเริ่มต้น

Make sure you have added a map and zone to the client. See Add Map and Add Device for details.

ขั้นตอน

1. Enter the E-map module.
2. Click Edit on the E-map toolbar to enter the map editing mode.
3. Click Add Hot Spot → Zone Hot Spot to open the Add Hot Spot panel.

4. Select the zone(s) to be added to the map.
5. ตัวเลือก: Edit the hot spot name, select the name color, and select the hot spot icon.
6. คลิก ตกลง

The zone is added to the map as a hot spot and its icon in the group list changes.

7. ตัวเลือก: Drag the zone hot spot to move it to a certain position. When alarms are triggered, the number of the newest alarms will be displayed on the zone's icon. You can click the number to see the alarms details.

8. ตัวเลือก: Click Clear Alarms to mark the alarms of the zones on the current map as read.

เพิ่มจุดเข้าถึงเป็นฮอตสปอต

You can add access points to the map as hot spots, so that you can find the hot spots and view their status and alarm numbers.

ก่อนเริ่มต้น

Make sure you have added a map and an access point to the client. See Add Map and Add Device for details.

ขั้นตอน

1. Enter the E-map module.
2. Click Edit on the E-map toolbar to enter the map editing mode.
3. Click Add Hot Spot → Access Point Hot Spot to open the Add Hot Spot window.

4. Select the access point(s) to be added to the map.
5. ตัวเลือก: Edit the hot spot name, select the name color, and select the hot spot icon.
6. คลิก ตกลง

The access point is added to the map as a hot spot and its icon in the group list changes.

7. ตัวเลือก: Drag the access point hot spot to move it to a certain position. When alarms are triggered, the number of the newest alarms will be displayed on the hot spot icon. You can click the number to see the alarms details.

กำหนดค่าฮอตสปอตเรดาร์รักษาความปลอดภัย

The client supports adding a security radar to the map to work as a hot spot. After that, you can configure parameters (including drawing zones and trigger lines, setting smart linkage, map calibration, etc.) for the radar and the parameters you set will take effect on the device. In this way, an intelligent monitoring in the radar's detection area can be realized by the client.

เพิ่มเรดาร์รักษาความปลอดภัยเป็นฮอตสปอต

For an effective monitoring, you can add a security radar to the map as a hot spot and paint zones in its monitoring field. So that when someone intrudes the zone, an alarm will be triggered for attention.

ก่อนเริ่มต้น

Make sure you have added an e-map and a security radar to the client. See Add Map and Device Management for details.

ขั้นตอน

1. Enter the E-map module.
2. Click Edit on the E-map toolbar to enter the map editing mode.
3. ตัวเลือก: Edit map scale. See Edit Map Scale for details.
4. Select a security radar in the device list and drag it to the map.

5. ตัวเลือก: Click the added radar and then click to edit the hot spot name, select the hot spot color, and select the hot spot icon.
6. คลิก ตกลง The security radar is added to the map as a hot spot and its icon in the group list changes. The sector indicates the monitoring field of the radar.

7. ตัวเลือก: Drag the security radar to move it to a certain position.

วาดโซน

Zone is a basic concept in the security control system. It refers to a protection area in a radar's detection area, and is regarded as the maximum recognizable unit to distinguish the alarm event, determining whether to trigger an alarm according to the zone type and radar's arming status. You can see the target's location on the map the minute an alarm is triggered so as to take quick actions accordingly.

ก่อนเริ่มต้น

Make sure you have disarmed the radar: click Finish, and select Disarm after clicking the radar's icon.

ขั้นตอน

1. Enter the E-Map module, and click Edit on the top right to enter the Edit mode.
2. ตัวเลือก: Enable Field Assistance on the top left of the map. The target track will appear on the radar detection area. You can draw a zone with reference to the track.
3. Click Radar Settings → Draw Zone Manually on the top of the map, and click the mouse to draw a zone on the radar detection area.

4. Right-click to complete drawing, and a window will pop up. Enter the zone name, and select Early Warning Zone, Warning Zone, or Disabled Zone as the zone type.
5. คลิก ตกลง
   • Early Warning Zone — Identifies targets that have potential risks in advance and triggers an alarm, but will not store alarm track. The early warning zone is green.
   • Warning Zone — Identifies the targets entering the area and triggers alarm. The warning zone is orange.
   • Disabled Zone — Blocks the target track in the area. The disabled zone is black.

6. Click Finish on the top right of the map.
7. ตัวเลือก: Edit or delete the zone after disarming the radar.
   1. Double-click the zone to enter the zone editing mode.
   2. Hover the cursor on the line of the zone and it will change to a cross, then click to add a marker.

3. Drag the marker to change the shape of the zone.

4. Hold to move the zone.

5. Click outside the zone to exit the zone editing mode.
6. Delete or edit the zone after entering the zone editing mode by double-clicking the zone.
   • Delete Zone — Click the delete button.
   • Edit Zone — Click the edit button to edit zone name and type.

วาดเส้นทริกเกอร์

A trigger line refers to a virtual line drawn in a radar's detection area on the map. An alarm will be triggered when someone crosses it in its pre-defined direction.

ก่อนเริ่มต้น

The radar is added to the map. Click Finish on the top right to exit the editing mode. Click on the radar icon and select Disarm to disarm the radar.

ขั้นตอน

1. On the E-map page, click Edit to enter the editing mode.
2. Click Radar Settings → Draw Trigger Line, and select Trigger Line or Dual-Trigger Line.

3. Draw trigger line.
   1. Click on the radar detection area to draw a trigger line.
   2. Select Left -> Right, Left <- Right or Left <-> Right in the pop-up window.
   3. ตัวเลือก: Enter the distance between two lines (only for dual-trigger line).

4. คลิก ตกลง
5. ตัวเลือก: Click on the trigger line to show different options: Edit, Delete and Move. You can edit the trigger line by clicking on it.
   • Add a Marker — Click on the line to add a marker.
   • Drag a Marker — Drag a marker on the trigger line to move it.
   • Move the Trigger Line — Hold the editing area to move the trigger line.
   • Edit — Click to edit the trigger line name, trigger line rule and distance (only for Dual-trigger Line).
   • Delete — Click to delete the trigger line.

เพิ่มพื้นที่ติดตามเท็จ

False track area is an area in radar's detection area. When an object enters the false track area, alarms will not be triggered, and the object's moving pattern will not be uploaded to the client. This function is applicable for places with plenty of disturbing factors (such as trees) that may cause wrong alarms.

ก่อนเริ่มต้น

Make sure you have added a radar to map and have disarmed the radar. See Add Security Radar as Hot Spot for details.

ขั้นตอน

1. On the top right of the map, click Edit to enter the editing mode of the map.
2. Click Radar Settings → False Track Area → Add False Track Area.
3. On the map, hold the mouse and drag to set the semi-diameter of the false track area. Right-click to end drawing.

4. ตัวเลือก: Perform the following operations.

ตั้งค่าการเชื่อมโยงอัจฉริยะ

Smart linkage works based on the calibration points you add to the radar's detection area. The calibration points tell the PTZ camera linked to the radar which direction to turn to when a target is detected so as to get the live view and track of the target by the client.

According to the relative installation position of the radar and the camera, it is necessary to select a schedule (One-Point Calibration or Multi-Point Calibration) for the calibration point selection.

• One-Point Calibration — Applicable to the scenario where the radar and the camera are installed on the same pole or the camera is installed within a radar-centered range of 2 meters (regardless of the altitude difference between the camera and the radar).

• Multi-Point Calibration — The scenario which is not applicable to the one-point calibration needs to adopt the multi-point calibration.

การปรับเทียบจุดเดียว

One-point calibration is applicable to the scene where the radar and the camera are installed on the same pole or the camera is installed within a radar-centered range of 2 meters (regardless of the altitude difference between the camera and the radar).

ก่อนเริ่มต้น

To perform this function, a cooperation between two persons is required. Person A enters the detection area so that Person B (the operator of the client) can see A's track on the client. Then B sets calibration points by the client according to A's track.

ขั้นตอน

1. Click Edit on the top right of the map.
2. Click Radar Settings → Smart Linkage Settings.
3. On the Smart Linkage Settings page, select a radar from the drop-down list on the top left.
4. Click a live view window at the bottom and select a camera in the Linked Camera list. The live view window displays the camera's live view.
5. Double-click the camera's live view window to enlarge it.

6. Select One-Point Calibration as the calibration mode.
7. Select the track of Person A. Ask Person A to move into the radar detection area. By comparing the moving object in the live view window of the camera and the track in the radar detection area, Person B needs to select the track of Person A and click it. The color of the selected track will turn from red to white.

8. Ask Person A to move to the calibration point within 20 to 40 m directly in front of the radar, and then stand at the calibration point.
9. Adjust the PTZ buttons in the live view window to get the PTZ position: Click + and - to adjust the altitude of Person A to two-thirds of the altitude of the window, and click the direction buttons to align the central sign with Person A (for precise alignment, click on the center of the object and the screen will adjust automatically).
10. Click Add Calibration to add a calibration point. The PTZ position and the radar position of Person A will be shown in the Information list. The option The smart linkage will be enabled after completing the settings will be checked automatically.

11. Click Save.

การปรับเทียบหลายจุด

Multi-point calibration is applicable to the scenario where the distance of the radar and the cameras linked to it is more than 2 meters.

ก่อนเริ่มต้น

This function needs the cooperation between 2 persons. Person A enters the detection area so that Person B (the operator of the client) can see A's track according to which B sets the calibration points by the client.

ขั้นตอน

1. On the Smart Linkage Settings page, select Multi-Point Calibration as the calibration mode.
2. Select calibration points (equally distributed) on the center line of the radar's detection area, you can refer to the following figure to select points.

3. According to the calibration points, Person A moves to a calibration point, and refer to steps 2 to 5 in One-Point Calibration to calibrate the calibration point.
4. When the first calibration point is set, let Person A move to the next calibration point after the yellow track disappears. Then refer to steps 2 to 5 in One-Point Calibration to set the next calibration point. Follow this process to set all other calibration points in turn.

5. Click Save after all calibration points are set.

การปรับเทียบ GPS

GPS Calibration refers to calibrating by device longitudes and latitudes, radar's orientation, and linked PTZ camera's position angle.

ก่อนเริ่มต้น

• Record the radar's longitude, latitude, and orientation.
• Record the linked PTZ camera's longitude, latitude, and position angle.

ขั้นตอน

1. On the Smart Linkage Settings page, click Set Longitude and Latitude to open the Set Longitude and Latitude window.
2. Enable Enable GPS Calibration.
3. Enter Radar Longitude, Radar Latitude, and Radar Orientation.

4. Enable Network Positioning System.

5. Enter Camera Longitude, Camera Latitude, and Position Angle.

6. คลิก ตกลง

การเรียนรู้ภูมิประเทศ

By terrain learning, the radar can get the terrain of its detection area and make more accurate smart linkage.

ก่อนเริ่มต้น

Make sure you have completed calibration. See One-Point Calibration and Multi-Point Calibration for details.

ขั้นตอน

1. On the Smart Linkage Settings panel, click Terrain Learning → Start Terrain Learning.
2. In the radar's detection area, select Person A's moving pattern.
3. Control the PTZ camera to keep Person A in the center of the live view page by the buttons on the right.

4. Click Terrain Learning → Finish Terrain Learning to end terrain learning.

5. ตัวเลือก: Click Terrain Learning → Clear Terrain Learning to clear existing terrain learning results.

การชดเชยการปรับเทียบ

Calibration Compensation makes calibration more accurate by adjusting Pan, Tilt, and Zoom of radar-linked PTZ camera.

ก่อนเริ่มต้น

Make sure you have finished a calibration.

ขั้นตอน

1. On the Smart Linkage Settings page, click Calibration Compensation to open the Calibration Compensation window.
2. Select a camera from the Camera list.

3. Select a Calibration Mode.
   • GPS Calibration — If you had conducted GPS calibration before, select this mode.
   • PTZ Calibration — If you had conducted one-point calibration or multi-point calibration before, select this mode.
4. Enter the Pan, Tilt, and Zoom.

5. คลิก ตกลง

ตั้งค่าจุดจอดสำหรับกล้องที่เชื่อมโยง

After enabling the radar parking mode, the radar will control the linked camera to turn to the predefined parking point when no target is detected within 10s in the radar detection area.

ก่อนเริ่มต้น

• Add the radar to the map.
• Link the camera to the radar, and add the camera to the client.
• Calibrate the camera and enable camera smart linkage.
• You need to disarm the radar before the operation. Click Finish on the E-map page to exit the editing mode. Click the radar icon and select Disarm to disarm the radar.

ขั้นตอน

1. Click Edit on the top right of the map to enter editing mode.
2. Click Radar Settings → Set Parking Point.
3. Select a radar from the Radar drop-down list.
4. Select a linked camera from the following list.
5. Use buttons on the right to adjust the camera screen center position (cross icon position) to the watch point. You can click on the screen and the screen will automatically adjust to the clicked center.

Adjust the rotation speed of the camera. 1 is the slowest and 7 is the fastest. 6. Click Set as Parking Point.

การปรับเทียบแผนที่

Map calibration is used to get the accurate scale of the map by the cooperation of three persons.

ก่อนเริ่มต้น

Make sure you have added the radar (when adding the device, check Import to Group) to the client and the map, and have set a scale for the map.

ขั้นตอน

1. Click Edit to enter the editing mode.
2. Click Radar Settings → Map Calibration.
3. To perform this operation, a cooperation between three persons is needed. Person A and Person B move into the radar's detection area. Person C selects their tracks by the client. A and B stop at the calibration points and the system will generate 2 markers at the terminal of tracks. Click OK on the pop-up window to confirm the terminal of the track or click Delete to select a new track.
4. Click on the map to confirm the actual locations of marker 1 and marker 2.
5. A window pops up saying Make sure the location on the map is correct and calibrate with the track terminal? Click Delete to delete all calibration points. Click OK on pop-up window. The system will automatically match the markers to the actual locations.

ฟังก์ชันอื่นๆ

When using the radar, you can perform some auxiliary functions such as arming/disarming, refreshing radar parameters, displaying OSD and PTZ camera's FOV (field of view), and enabling alarm output to meet different needs.

Arm/Disarm All Radars

Click Arm Radar → Arm All Radars/Disarm All Radars to arm or disarm all radars on the map.

Arm/Disarm Single Radar

After exiting the editing mode, click the radar's icon to show its operation menu.

• Arm a Radar — Arm the radar's detection area. A question will pop up saying There are targets in the zone, enable mandatory arming? if you arm the radar when a target exists in the warning zone. You can click OK to arm the radar mandatorily.

• Disarm a Radar — Disarm the radar's detection area.

Event

Search alarms triggered by certain cameras during certain time range, and view the alarm related videos. See Preview Hot Spot for details.

Enable Alarm Output

An alarm output refers to sirens linked to a radar. It flashes or generates alarm sound when an alarm or pre-alarm is triggered if you enable it.

Operation: click Radar Settings → Alarm Output after entering editing mode. Select a relay, and switch on in the Operation column; or click Enable All to enable all the relays in the list.

Display OSD

On the top of the map, click Radar Settings → Display OSD to display the detected target's moving speed and the distance between the target and radar.

Display PTZ Camera's FOV

On the top of the map, click Radar Settings → Camera FOV to display the linked PTZ camera's field of view (FOV) and camera's IP address on the map.

Refresh

Click Radar Settings → Refresh on the top of the map to refresh the radar's newest detection angle, detection distance, trigger lines, and arming status.

แก้ไขฮอตสปอต

You can edit the information of the added hot spots on the map, including the name, the color, the icon, etc.

ขั้นตอน

1. Enter the E-map module.
2. Click Edit in the upper-right corner to enter the map editing mode.
3. Select the hot spot icon on the map and then click to open the Edit Hot Spot window.
4. Edit the hot spot name in the text field, select the hot spot name's color and hot spot icon shown on the map.
5. Check Apply to Other Camera Hot Spots / Apply to Other Alarm Input Hot Spots / Apply to Other Alarm Output Hot Spots / Apply to Other Zone Hot Spots to apply the color and icon settings to other hot spots.
6. คลิก ตกลง

7. ตัวเลือก: Select the hot spot icon and click the delete button to delete the hot spot.

ดูตัวอย่างฮอตสปอต

After adding hot spots (including camera, alarm input/output, zone, security radar, and zone) to the map, you can view the live view of the camera hot spot and the triggered alarm information of all the types of hot spots on the map.

ก่อนเริ่มต้น

Make sure you have added hot spots to the map. See Manage Hot Spot for details.

ขั้นตอน

1. Enter the E-map module.

2. Click Display to show the hot spots on the map.

3. Click a hot spot to perform the following operation(s).

4. ตัวเลือก: Perform the following operation(s).